草榴社区 Cloud
Cloud native EDA tools & pre-optimized hardware platforms
Request a Free Trial →
Simpleware Case Study: A Novel Simulation for Detecting Iliopsoas Tendonitis After Different Hip Surgeries
Overview
Iliopsoas tendonitis, typically caused by impingement between the iliopsoas tendon and the acetabular cup, affects about 18% of total hip arthroplasty (THA) and 30% of hip resurfacing arthroplasty (HRA) patients. A novel simulation for detecting iliopsoas impingement has been developed and validated in THA patients.
In this study, validation was extended to HRA patients, and results compared between THA and HRA patients. Using Simpleware software, CT scans from two cohorts of 12 patients were segmented, landmarked, and exported for simulation. Results showed, the simulation significantly predicted iliopsoas tendonitis and differentiated between the symptomatic and asymptomatic cohorts in investigations of THA and HRA patients. This novel simulation offers potential for preoperative cup placement decisions and postoperative iliopsoas tendonitis diagnosis.
Highlights
- A novel simulation for detecting iliopsoas impingement has been developed and validated
- Simpleware software used to segment and landmark CT scans
- Simulation significantly predicts iliopsoas tendonitis
- Tool has potential to improve preoperative and postoperative surgical decision-making
Reference
Hardwick-Morris M, Twiggs J, Miles B, et al., 2024. , J Orthop Res, 42(7), 1577-1586.
Thanks to
- ()
"The Simpleware platform is a feature rich environment for very quickly setting up in-silico studies. Its extensive capabilities and ease of use significantly lowers the barrier to trying out new concepts; without access to tools like it we may well have never been able to start this project."
Joshua Twiggs, Head of Research & Development, 360 Med Care
Introduction
Hip resurfacing arthroplasty (HRA) is an alternative surgical treatment to total hip arthroplasty (THA) for end-stage osteoarthritis (OA) of the hip. HRA demonstrates equivalent revision rates whilst preserving more bone stock and better restoring native biomechanics than THA. However, groin pain, specifically iliopsoas tendonitis, remains a common complication after HRA. It is most frequently caused by impingement of the anterior edge of the acetabular cup with the iliopsoas tendon, due to lateralization, under-anteversion, or oversizing of the acetabular implant, among other factors.
Building on a previous simulation of THA, this study examined the mechanisms behind iliopsoas tendonitis in HRA patients using a case-controlled investigation of symptomatic and asymptomatic patients. These results were then compared to the previously collected THA results to find differences in cup impingement and tendonitis mechanisms.
Two hypotheses were tested in this study. First, the symptomatic cohort of HRA patients would demonstrate significantly greater levels of impingement than the asymptomatic HRA patients in both supine and standing positions. Second, the impingement in the symptomatic HRA cohort would exceed that of the previously studied THA cohort due to the larger acetabular cups associated with HRA.
Patient Selection
A retrospective search was conducted from a surgeon’s database for patients who underwent HRA surgery and were diagnosed with iliopsoas tendonitis. Inclusion criteria included levels of pain in different leg positions, and patients who had undergone HRA followed by a postoperative CT scan, and a standing X-ray with a minimum of 6 months’ follow-up. Exclusion criteria focused on patients with elevated metal ion levels. After application of the inclusion and exclusion criteria, 12 symptomatic patients remained. The asymptomatic cohort consisted of 12 patients from the same surgeon's database who had undergone HRA surgery but had not been diagnosed with iliopsoas tendonitis.
This comparison between experimental and control cohorts was undertaken as it demonstrates that the simulation can distinguish between symptomatic and asymptomatic patients. The primary outcomes of the study were the differences in impingement between the symptomatic and asymptomatic HRA cohorts, and the symptomatic THA and HRA cohorts. Secondary outcomes were differences in cup orientation, supine and standing pelvic tilt, cup prominence, or implant sizes between the symptomatic and asymptomatic HRA cohorts.
CT scan showing the location of the iliopsoas (psoas) tendon.
Model Generation
3D models of each patient's pelvis and operative femur were generated in Simpleware software by segmenting the CT scans using a combination of manual segmentation and in-built functions. The hip resurfacing implants were imported and registered to their in-situ positions.
Segmented postoperative hip CT scan with a registered hip resurfacing implant in Simpleware software.
The iliopsoas insertion points, anterior pelvic plane (APP) landmarks (left and right anterior superior iliac spine points and the pubic symphysis), and the femoral head center were landmarked in Simpleware. Quality checks at various stages of the process confirmed accuracy of the placements of the landmarks and implants. Meshes of the bony anatomy and registered implants were then exported in their supine (CT) positions.
Landmarks placed on a segmented hip CT scan in Simpleware software.
Simulation of Iliopsoas Impingement
A representation of the iliopsoas was generated using a novel approach to tracing the path from three superior insertion point of the iliopsoas to the inferior insertion point at the lesser trochanter (LT). The three superior insertion points are located on the lateral superior plateau and transverse process of the L5, and near the sacroiliac joint. These reproducible landmarks are present in all CT scans and accurately represent the iliopsoas’ width and location it passes over the acetabular margin. Each combination of superior and inferior insertion sites was used to create a segment for simulation, with each containing a green path (excluding the acetabular cup) and red path (including the acetabular cup) path wrapping around the pelvis, prosthetic femoral head, and operative femur. Impingement was quantified as the difference between these two path lengths, or the ‘stretch’ of the iliopsoas due to the acetabular cup.
Schematic of the iliopsoas impingement simulation with three segments representing the approximate width of the iliopsoas and the location it passes over the acetabular margin.
In cases without iliopsoas impingement, the green and red path lengths are equal. However, in cases with impingement, the red path is longer than the green path. Three separate impingement values were obtained from the segments and calculated and reported as the mean and maximum of these values. The pelvis was then rotated to obtain the patient’s standing pelvic position, resulting in four iliopsoas impingement measurements per patient. Cup prominence was also measured using a method from the literature, and statistical analysis conducted using a range of metrics to determine clinical significance and other variables such as simulation sensitivity and specificity.
Results
The study demonstrated no statistically significant difference between symptomatic and asymptomatic cohorts for cup anteversion, cup inclination, cup size, femoral head size, supine pelvic tilt, or standing pelvic tilt. However, statistically significant differences were found for the symptomatic versus asymptomatic cohorts for the mean cup prominence, the average supine mean impingement, the average standing mean and standing maximum impingements, and the average supine maximum impingement. Cup prominence, standing mean impingement and standing maximum impingement significantly predicted the probability of iliopsoas tendonitis in logistic regression models.
Cup prominence results for the symptomatic and asymptomatic cohorts. The symptomatic cohort had significantly greater cup prominence values.
Conclusions
The novel iliopsoas impingement detection simulation has been validated in studies of HRA and THA patients, showing it can detect iliopsoas impingement and distinguish between symptomatic and asymptomatic patients. The symptomatic HRA cohort had significantly greater impingement than the asymptomatic cohort, and the simulation predicted iliopsoas tendonitis with high sensitivity and specificity.
Interestingly, the symptomatic THA cohort showed greater impingement than the HRA cohort, contradicting the original hypothesis that more impingement would be observed in the HRA due to the use of larger cups. Current explanations of this finding suggest that iliopsoas tendonitis and impingement are three-dimensional problems, not merely related to the prominence of the cup when measured on a 2D axial slice of a CT scan. Therefore, further study is needed to understand the incidence of iliopsoas tendonitis after both types of hip arthroplasty.
The study also highlighted the multicausal nature of iliopsoas tendonitis, with two symptomatic patients showing no impingement (referred to as "false negatives"). For one of these patients, the availability of a preoperative CT scan allowed for the reconstruction of the preoperative bony anatomy in Simpleware software and the simulation of a representation of the iliopsoas. The analysis found that the iliopsoas had been lengthened by about 5 mm from preoperative to postoperative states, potentially through anteriorisation of the prosthetic femoral head, which may have been leading to pain and irritation. The sample sizes in the current studies are not large enough to draw any conclusions, and future research should explore additional factors behind iliopsoas tendonitis across larger cohorts, considering factors like age, gender, and activity level.
This study was novel for providing insight into the level of anterior cup exposure observed in HRA patients diagnosed with iliopsoas tendonitis. The simulation has the potential to be used as part of a 3D preoperative templating workflow to assist in optimizing cup orientation and positioning.
Any Questions?
Do you have any questions about this case study or how to use Simpleware software for your own workflows?